|
 Xerox
C123 style Copiers – Part 4
Component Control Test Codes for the Xerox CopyCentre C123, C128,
& WorkCentre M123, M128, Pro123, Pro128 and WorkCentre 5222, 5225,
5230
Now, we’ll
continue from the last month issue to review the Output Codes. The
Output Codes (for motors, solenoids, clutches, lamps, etc.) are
accessed the same way as the input codes. When you enter the
Chain-Link code for a motor or clutch, each time you press 'Start'
the component will turn on or off. Below is a list of the Output
Codes with the finisher codes missing and the duplicate codes
eliminated:
|
OUTPUT CODES (for Testing Motors, Solenoids, Clutches, etc.) |
|
Chain-Link |
Name |
Meaning |
| 005-001
|
Document Feed Motor (speed 1) |
H = Motor is on |
| 005-102
|
Document Presence Sensor |
L = Paper detected by Document In
Sensor |
| 005-110
|
Document Registration Sensor (Belt
DADF/CVT) |
Document Detected |
| 005-224
|
Scan Start Signal |
H = Scan Start Signal is ON |
| 012-110
|
Registration Clutch ON |
H = Clutch Engaged (Reg. Roll should
resist turning when engaged (H) and should turn easily when
disengaged (L). |
| 042-001
|
Main Drive Motor |
Same as Name
|
| 042-002 |
Fuser Fan Motor (High Speed) |
Fuser Fan changes from Low to High Rotation.
|
| 042-003
|
ROS (Laser Unit) Fan |
ROS Fan On / Off (note: virtually inaudible) |
| 047-001
|
Offset Motor 1 Forward |
OCT1 (Oscillating Catch Tray) Exit Roll
Rotates Forward |
| 047-003
|
Offset Motor 2 Forward |
OCT2 Exit Roll Rotates Forward |
| 047-004
|
Offset Motor 2 Reverse |
OCT2 Exit Roll Rotates in Reverse |
| 047-005
|
Offset Motor 1 Reverse |
OCT1 Exit Roll Rotates in Reverse |
| 047-022
|
Exit Drive Motor - Forward |
Drives paper out to Exit |
| 047-023
|
Exit Drive Motor - Reverse |
Drives paper into the Duplex Module |
| 047-024
|
Exit Gate Solenoid |
Switch Gate to Exit 2 (Face Up Tray) |
| 047-025
|
Face Up Gate Solenoid |
Switch Face Up Tray Gate to Face Up Tray
|
| 061-001
|
ROS (Laser Unit) Motor |
ROS Motor On / Off (Laser Polygon Motor) |
| 071-001
|
Tray 1 Feed / Lift
Motor - Reverse |
Turns Lift Motor on to lift tray (reverse of
feed direction) for two seconds when Tray 1 Up Sensor is ''L''
(Down). Will not turn on if Tray 1 Up Sensor is ''H'' (Up
Position) |
| 071-002 |
Tray 2 Feed / Lift Motor - Reverse |
Turns Lift Motor on to lift tray (reverse of
feed direction) for two seconds when Tray 2 Up Sensor is ''L''
(Down). Will not turn on if Tray 2 Up Sensor is ''H'' (Up
Position) |
| 071-003
|
Tray 3 Feed / Lift Motor - Reverse |
Turns Lift Motor on to lift tray (reverse of
feed direction) for two seconds when Tray 3 Up Sensor is ''L''
(Down). Will not turn on if Tray 3 Up Sensor is ''H'' (Up
Position) |
| 071-004
|
Tray 4 Feed / Lift Motor - Reverse |
Turns Lift Motor on to lift tray (reverse of
feed direction) for two seconds when Tray 4 Up Sensor is ''L''
(Down). Will not turn on if Tray 4 Up Sensor is ''H'' (Up
Position) |
| 071-007
|
Tray 1 Feed / Lift Motor - Forward |
Motor turns forward in feed direction |
| 071-008
|
Tray 2 Feed / Lift Motor - Forward |
Motor turns forward in feed direction |
| 071-012
|
SMH Feed Clutch |
Same as Name |
| 071-037
|
Drum Drive Motor |
Same as Name |
| 073-006 |
Takeaway Motor |
Same as Name
|
| 073-009
|
Tray 3 Feed / Lift Motor - Forward |
Same as Name |
| 073-010
|
Tray 4 Feed / Lift Motor - Forward |
Same as Name |
| 073-013
|
TM Takeaway Clutch |
Same as Name |
| 073-016
|
Duplex Drive Motor |
In high speed (process speed)
|
| 073-018
|
HOT-LINE CHECK with alternative signal
|
Hot-Line Control - MCU (Main Control Unit)
toggles FEED-STOP signal alternatively. Tray Module toggles
FEED-READY signal. |
| 073-019
|
Tray 3 Feed / Lift Motor - Forward
(Hot Line) |
Hot-Line Control |
| 073-020
|
Tray 4 Feed / Lift Motor - Forward (Hot
Line) |
Hot-Line Control |
| 073-026
|
Duplex Exit Motor |
Motor runs to move paper out to
registration. In low speed (process speed)
|
| 089-002
|
Registration Clutch |
Same as Name
|
| 091-002
|
BCR (Bias Charge Roll) AC Bias Voltage |
The BCR AC, BCR DC, Developer Bias, BTR
output simultaneously. * |
| 091-003
|
BCR (Bias Charge Roll) DC Bias Voltage |
The BCR AC, BCR DC, Developer Bias, BTR
output simultaneously. * |
| 091-004
|
DTS |
Same as Name |
| 091-007
|
Developer DC Bias Voltage |
The BCR AC, BCR DC, Developer Bias, and BTR
output simultaneously. * |
| 091-010
|
BTR (Bias Transfer Roll) (-) Bias Voltage |
The BCR AC, BCR DC, Developer Bias, and BTR
output simultaneously.* |
| 093-001
|
Toner Dispense Motor |
Same as Name |
| 094-001
|
BTR (Bias Transfer Roll )(+) Bias Voltage |
The BCR AC, BCR DC, Developer Bias, BTR
output simultaneously.* |
* A bunch of the
codes which relate to the various high-voltage tests all activate
simultaneously from any one of their codes: BTR (Bias Transfer
Roll), BCR-AC & BCR-DC (Bias Charge Roll), & Developer Bias. You
can also test these independently of each other but to do so would
require first going into the NVM Memory settings and then changing
the setting for 751-560 from the default value of '0'
(simultaneous output) to a '1' (single output).
That just about rounds out the information for the C123 style for
the time being. Happy troubleshooting to you all!
Britt works for
The Parts Drop, a company whose primary business is providing
parts, supplies and information for Xerox brand copiers, printers
and fax machines. You can find more information, including many of
Britt's past ENX articles on their website,
www.partsdrop.com. If you'd
like to read more about Xerox brand office equipment, there's also
a complete listing of past articles under contributing writers on
the ENX website - www.ENXMAG.com
|
|
